ASTM B407 PDF

Incoloy , H, and HT are nickel-iron-chromium alloys with good strength and excellent resistance to oxidation and carburization in high-temperature exposure. These nickel steel alloys are identical except for the higher level of carbon in alloy H, and the addition of up to 1. Incoloy was the first of these alloys and it was slightly modified into Incoloy H. This modification was to control carbon.

Author:Fejar Shaktirn
Country:Sri Lanka
Language:English (Spanish)
Genre:Politics
Published (Last):2 January 2004
Pages:468
PDF File Size:18.56 Mb
ePub File Size:4.95 Mb
ISBN:126-2-55571-366-7
Downloads:68647
Price:Free* [*Free Regsitration Required]
Uploader:Duran



A number in parentheses indicates the year of last reapproval. A superscript epsilon e indicates an editorial change since the last revision or reapproval. The values given in parentheses are for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identi? Referenced Documents 2. Current edition approved March 1, Published April Originally approved in Last previous edition approved in as B — E 29 Practice for Using Signi?

Terminology 3. Ordering Information 4. NOTE 1—Tube produced to outside diameter and minimum wall may be furnished upon agreement between the manufacturer and the purchaser. No further reproductions authorized. A Iron shall be determined arithmetically by difference.

Alloy UNS N 0. UNS N B See If threaded ends or ends beveled for welding are desired, give details. Materials and Manufacture 5. Chemical Composition 6. Mechanical Properties and Other Requirements 7. The pipe or tube shall show no evidence of leakage. If eddy current testing is used, the following test method would apply: 7.

The eddy-current examination referenced in this speci? The discontinuity shall be placed in the weld if visible. Said notch shall have a depth not exceeding ? To be accepted, retested material shall meet the original electric test requirements. Dimensions and Permissible Variations 8. Thus, if outside diameter and wall are speci? Similarly, if outside diameter and inside diameter are speci?

B For pipe and tube, in all tempers, with an inside diameter of less than 1? D Eccentricity—The variation in wall thickness in any one cross section of any one cold-? E For tube 5 in. For tubes over 5 in. G If tube is speci? H The wall thickness tolerance includes eccentricity tolerance up to For small-diameter and light-wall tube, material shall conform to the applicable requirements of Table X3.

The camber depth of chord of hot-? For sizes over 5 in. Workmanship, Finish, and Appearance 9. Sampling Number of Tests Specimen Preparation When testing in full tubular size is not possible, longitudinal strip specimens, or the largest possible round specimen, shall be used. In the event of disagreement when full tubular testing is not possible, a longitudinal strip specimen with reduced gage length as contained in Test Methods E 8 shall be used.

Test Methods Inspection Rejection and Rehearing In case of dissatisfaction with the results of the tests, the manufacturer may make claim for a rehearing within that time. When speci? Product and Package Marking The material marking shall be by any method which will not result in harmful contamination. Keywords Other schedules may be furnished, and the manufacturer should be consulted.

Table X1. Schedule No. These are subject to change and the manufacturer should be consulted for the latest information available. Available in sizes 1? Intended generally for machined parts where the oxide surface will be removed.

The material is furnished in a limited range of sizes and the manufacturer should be consulted as to the various outside diameters and wall thicknesses that may be furnished. Material will have a bright? Such material shall conform to the applicable requirements for the conditions indicated in Table X3. C Hardness values, indicative of tensile strength, are shown for information only. All tests are subject to con?

For hardness conversions see Hardness Conversion Tables E Inches Under 3? Over Permissible Variations, in. Under Under 1 up to 1. C Wall Tolerances, Light-Wall Tube—The plus and minus wall tolerance shown in the table shall apply down to and including 0. For wall thicknesses less than 0. D Random Lengths:Where nominal random lengths on tubing 1? This is a total spread of 7 ft cm. Random lengths in sizes 1? Long random lengths are subject to a range of 15 to 22 ft to cm.

Random lengths in sizes up to, but not including 1? E Cut Lengths—Tolerances on cut lengths shall be as follows: F Straightness—Round tubing is subject to a straightness tolerance of one part in equivalent to a depth of arc of 0.

G Eccentricity—Eccentricity as de? H When speci? However, when not speci? It should be noted that inside diameter tolerances are based upon the outside diameter range. Approved March 1, ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phone , fax , or service astm.

HARLEQUIN PHILIP SPARKE PDF

Astm B 407 Incoloy 800h / 800ht Uns N08810/N08811 Nickel Alloy Steel Tube

A number in parentheses indicates the year of last reapproval. A superscript epsilon e indicates an editorial change since the last revision or reapproval. The values given in parentheses are for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identi? Referenced Documents 2.

COWON IAUDIO 7 MANUAL PDF

ASTM B407/B358 Incoloy 800HT Pipe

It covers them in the form of cold-worked or hot-finished annealed seamless pipes and tubes. They are annealed to produce controlled grain size required for optimum properties in this temperature range. These Incoloy alloys possess very high resistance to chloride-ion stress-corrosion cracking, and also exhibits good resistance to polythionic acid cracking. Hence, these pipes and tubes are highly applicable in high temperature petrochemical environments. Scope And Manufacturing As per ASTM B specifications ,the alloys should be heat treated at specified annealing temperatures and should adhere to the chemical composition limits for nickel, chromium, iron, manganese, carbon, copper, silicon, sulfur, aluminum, titanium, columbium, molybdenum, niobium, tantalum, phosphorus, tungsten, cobalt, nitrogen, and boron as specified in ASTM B specification.

EILEEN MCENTEE COMUNICACION ORAL PDF

ASTM B407 Incoloy 800HT Pipe

.

BORGES EL JARDIN DE LOS SENDEROS QUE SE BIFURCAN PDF

ASTM B407 Tubing

.

Related Articles