Zulujar This statement Chrysler provides in accompaniment with this chart reveals some computer math strategy. A real sure way to prevent fluid from ever wicking up the wires again is to expose a piece of each of the wires and drop some solder on the wire. Too many wives might find oily residue on their dishes after removing them from their dishwasher. The selector lever can then be safely placed into Reverse or Drive to properly conduct the test. Crazy as it sounds, it happens. Another misunderstood scan tool parameter that occurs is with the Transmission Fluid Temperature located in the electrical conductor plate as ztsg in Figure This transmission does not have an output speed sensor.
|Published (Last):||11 September 2007|
|PDF File Size:||19.91 Mb|
|ePub File Size:||1.47 Mb|
|Price:||Free* [*Free Regsitration Required]|
Nejinn This transmission does not have an output speed sensor. Too fast of a release with the off-coming clutch and the shift will transition will consist of a slight engine flare making it feel like a slip. I know that there are transmissions with computers being inside them submersed in transmission fluid, but these external TCMs are not one of them and do not fare well being filled with fluid.
Because this plate can fail in such a way where it will produces speed sensor or solenoid codes, there has been at times confusion with diagnosing the N2 and N3 speed sensors. The chart in Figure 10 confirms the normal operation of the speed sensors, the N3 sensor being at 0 in reverse S1st and 5th gears while the N2 is providing an rpm reading.
Here is a strong diagnostic article for you. Jenric Auto Sales Car Dealership. What this means to you and me is this. Mercedes The N2 rpm of is divided by the 0. Several different gear ratios are available with this transmission as well as various amounts of clutch plates within a clutch pack assembly.
The ISS Factor Making sure the clutch is used properly is almost as important as these other tips for keeping this transmission in gear. Although the adapter plug is supposed to prevent transmission fluid from leaking fluid into the harness connector, it could fail.
This means that anytime the input shaft is in rotation so is the front planetary carrier assembly. Tasg is mounted on the valve body, which the solenoids bolt down onto Figure 7. The N3 speed sensor solid black is the most forward asg sensor on the conductor plate. ATSG It began with the Chrysler and Dodge Magnum.
But it will definitely ensure that the new TCM you put in will not atsy loaded with fluid again. This gets driven by the front ring gear attached to the K2 clutch drum and input shaft. This occurs in Park, Reverse Atsh Mode, 1st and 5th gear. TransTec de Corteco Cars.
The computer is programmed to divide the 0. Some risk cleaning out the contaminated TCM to reuse it. Another misunderstood scan tool parameter that occurs is with the Transmission Fluid Temperature located in the electrical conductor plate as shown in Figure Then both are the same in 2nd, 3rd, and 4th.
It will take some time to stagger the exposure of each wire, solder, and then properly wrap and cover your work. This gives the transmission the capability to be fitted behind engines as small as a 4 cylinder to as strong as a 12 cylinders.
With some Mercedes-Benz vehicles, there atwg been reports of transmission fluid being accidently poured into the engine oil fill hole after repairs. As a side note, the N2 rpm reading in 1st and 5th gear will not be actual input shaft rpm. A real sure way to prevent fluid from ever wicking up the wires again is to expose a piece of each of the wires and drop some solder on the wire.
The remedy is a new sleeve between the internal conductor plate and external harness connector called the Adapter Plug; part number A 02 53 Figure 6. The part number to replace it is, A 11 Interestingly tasg, the advertised atsf ratios for this vehicle are as follows: This value is then used to monitor gear ratio health of the transmission by the computer. Figure 11 is a first gear screen capture at 10mph of a Jeep Grand Cherokee which provides the following data:.
This sensor reads the rotation of the K1 clutch drum inside the transmission Figure 9. This drum has the front planetary sun gear attached to it and it lugs into the B1 clutch on the pump. The selector lever can then be safely placed into Reverse or Drive to properly conduct the test.
Sections of this page. Integral to this conductor plate is the starter interlock contact, transmission oil temperature sensor, the N2 and N3 speed sensors. Related Posts
722.6 ATSG PDF
Atsg 722.6 Manuals